Clearone-comm PSR1212 Manual de usuario Pagina 107
- Pagina / 145
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
101
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
DFLTM - Default Meter
This command selects/reports the setting of the default meter.
Command form: DEVICE
DFLTM
[Channel] [Group] [Position]
Argument details
Name Description
Device 0–7 or * to select all units
DFLTM Command form
Channel 1–12
Group I = Inputs, O = Outputs, M = Mic Inputs, L= Line Inputs
Position I, A, N, G, as applicable for group
(see Meter Type definitions, page 94)
Example:
#45 DFLTM 8 O A
On PSR1212 unit 5 (
#45
), the default meter
(
DFLTM
) is set to output (
O
)
8
after the gain adjustment (
A
).
DID - Device ID
This command selects/reports the device ID.
Command form: DEVICE
DID
[Value]
Argument details
Name Description
Device 0–7 or * to select all units
DID Command form
Value 0–7 (select device ID)
Example:
#47 DID 0
On PSR1212 unit 7 (
#47
), the device ID (
DID
) is set to
0
.
Appendices ~ Appendix E: Serial Commands
- PSR1212 Digital Matrix Mixer 1
- PSR1212 Installation and 2
- Operation Manual 2
- ClearOne Part No. 800-155 2
- 001 Jan 2007(Rev. 7.1) 2
- Table of Contents 3
- CHAPTER 1: Introduction 7
- New Features 8
- Unpacking 10
- Front panel 10
- Controls and Connections 10
- Rear panel 11
- Networking 13
- Expansion bus 13
- CHAPTER 2: Installation 15
- To connect the unit 16
- Expansion bus connections 17
- Networking Units 17
- Device IDs 18
- Mixer mode 18
- LCD menu tree 19
- LCD Programming 19
- System menu 20
- RS-232 menu 21
- Meter menu 22
- Inputs menu 23
- Outputs menu 24
- = Meter Reference Point 25
- CHAPTER 3: System 27
- Configuration 27
- Creating Floppy Disk Copies 28
- To install G-Ware 28
- Installing G-Ware 28
- Site Setup 29
- Creating a new site 29
- Adding a PSR1212 30
- Configuring Unit Properties 31
- Flow Screen 33
- G-Ware Screens 33
- Status bar 34
- Copying and pasting settings 34
- Safety Mute 34
- Matrix Screen 35
- Expansion bus O–Z routing 36
- Process A–H routing 36
- Cross point attenuation 36
- Audio Routing 36
- Matrix report 37
- Inputs 1–8 38
- Inputs and Outputs 38
- Active Filter 39
- To configure filters 41
- Activation 41
- Decay Rate 43
- PA Adapt and AEC Reference 43
- Figure 3.31 44
- Virtual Reference 44
- Gating Group Select 45
- Pre Gain 47
- Post Gain 47
- Post Processing 47
- Post Gating 47
- Inputs 9–12 48
- Outputs 1–12 50
- Max adjust 51
- Min adjust 51
- Figure 3.42 51
- Output gain adjust 51
- From Expansion Bus O–Z 52
- To Expansion Bus O–Z 52
- Expansion Buses 52
- Processing A–H 53
- Processing 53
- Cmprs (compressor) 54
- Figure 3.49. Delay window 57
- Figure 3.50. Process 58
- CHAPTER 4: Advanced 59
- Preset Configuration pane 60
- Figure 4.4. Preset Mask 61
- Control/Status B 61
- To create a preset 63
- Storage space 63
- Running presets 64
- Room combining example 65
- Creating macros 67
- Figure 4.16 Macro Name window 68
- Figure 4.14 68
- Macro Editor button 68
- Editing macros 69
- Running macros 70
- CHAPTER 5: Operation 71
- Document Compare Utility 72
- Operation ~ Utilities 73
- Copying settings 74
- Print Reports 75
- GFirm Firmware Utility 76
- G-Ware Switcher 78
- Copy and paste settings 79
- Message Log 79
- Gate View 79
- Monitoring Views 79
- Meter Views 80
- CHAPTER 6: Control 81
- XAP IR Remote 82
- Remote Builder 82
- ClearOne Control Panels 83
- Control ~ Remote Builder 84
- To program the Volume panel 84
- To program the Select panel 85
- Remote Modem Access 86
- Serial commands 86
- RS-232 Port 86
- Command strings 87
- APPENDICES 89
- Appendix B: Pinouts 90
- Control/Status connectors 91
- Control/Status B port pinout 92
- Set connector pinout 93
- Line connector pinout 93
- Appendix C: Control Panel 94
- Connecting the Control Panel 94
- Control Panel Assembly 95
- Dimensions (both 95
- Appendix D: Accessories 97
- Conventions 98
- Command structure 98
- Appendix E: Serial Commands 98
- Groups and channels 99
- Type and device IDs 99
- Meter type definitions 100
- Serial command error codes 100
- PSR1212 Serial commands 101
- AMBLVL - Ambient Level Adjust 103
- AAMB - Adaptive Ambient Mode 103
- AGC - Automatic Gain Control 103
- BAUD - Baud Rate 104
- COMPRESS - Compressor Adjust 105
- COMPSEL - Compression Select 105
- DECAY - Decay Adjust 106
- DELAY - Delay Adjust 106
- DELAYSEL - Delay Select 106
- DFLTM - Default Meter 107
- DID - Device ID 107
- FILTER - Filter Adjust 108
- FILTSEL - Filter Select 109
- FLOW - Flow Control 109
- FMP - First Mic Priority Mode 109
- FPP - Front Panel Passcode 110
- GAIN - Gain Adjustment 110
- GATE - Gate Status 111
- GHOLD- Gate Hold Time Adjust 111
- GMODE - Gating Mode 112
- GOVER - Gating Override 112
- GRATIO - Gate Ratio Adjust 112
- GREPORT - Gate Report 113
- GRPSEL - Gating Group Select 113
- LABEL - Label 113
- LFP - Lock Front Panel 114
- LMO - Last Mic On Mode 114
- LOCK - Preset and Macro Lock 114
- LVL - Level 115
- LVLREPORT - Level Report 116
- LVLRRATE - Level Report Rate 116
- MAX - Maximum Gain Setting 117
- MDMODE - Modem Mode 118
- MIN - Minimum Gain Setting 118
- Example: 119
- MLINE - Mic/Line Adjust 120
- MPASS - Modem Password 120
- MTRX - Matrix 121
- MUTE - Mute 122
- OFFA - Off Attenuation Mode 122
- PAA - PA Adaptive Mode 123
- PP - Phantom Power 123
- PRGSTRING - Program String 124
- RAMP – Ramp Gain Adjustment 125
- SERECHO - Serial Echo 126
- SERMODE - Serial Mode 126
- SFTYMUTE - Safety mute 127
- SIGGEN - Signal Generator 127
- STRING - String Execution 128
- TOUT - Time Out Select 128
- UID - Unit ID 129
- VER - Version 129
- Appendix F: Warranty 130
- FCC Part 15 Compliance 132
- Safety Information 132
- Appendix G: Compliance 132
- Glossary 133
© 2020, manymanuals.es. Todos los derechos reservados | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales